• <li id="4u0ko"></li>
    <nav id="4u0ko"></nav>
  • <legend id="4u0ko"></legend>
  • <input id="4u0ko"><noscript id="4u0ko"></noscript></input>
    自上料攪拌車廠家

    全國咨詢熱線

    400-879-1999

    點擊撥打服務熱線:400-879-1999
    你所在位置: 首頁 >> 自動上料攪拌車資訊 > 行業資訊 >

    行業資訊

    自上料攪拌機中如何利用氣流?

    作者:http://www.kenguscpas.com 時間:2021-03-05

    氣流攪拌是利用氣體鼓泡通過液 體層,對液體產生攪拌作用,或使氣泡群一密集狀態上升借所謂上升 作用促進液體產生對流循環。與機械攪拌相比,僅氣泡的作用對液體 進行的攪拌時比較弱的,對于幾千毫帕·秒以上的高粘度液體是難于 使用的。但氣流攪拌無運動部件,所以在處理腐蝕性液體,高溫高壓 條件下的反應液體的攪拌時比較便利的。
    Gas stirring is the use of gas bubbles through the liquid layer, to produce stirring effect on the liquid, or make the bubble group a dense state rise, by the so-called rising effect to promote the liquid convection circulation. Compared with mechanical stirring, the effect of bubbles on liquid stirring is weaker, and it is difficult to use for high viscosity liquid with several thousand MPa · s. However, there are no moving parts in the air flow stirring, so it is more convenient to deal with corrosive liquid and reaction liquid under high temperature and high pressure.
    在工業生產中,攪拌操作時從化學工業開始的,圍繞食品、纖維、造紙、石油、水處理等,作為工 藝過程的一部分而被廣泛應用。攪拌操作分為機械攪拌與氣流攪拌。
    In industrial production, mixing operation starts from the chemical industry, and is widely used as a part of the process around food, fiber, paper, oil, water treatment, etc. Mixing operation is divided into mechanical mixing and air mixing.
    自上料攪拌車
    不要在有孔的分支上使用焊接工具,因為這樣會損壞襯層。攪拌機的射孔支管不得使用電焊(氣焊)工具,因為電焊會破壞攪拌機的內襯塑料,支管的連接必須用專用管件進行坡口連接;攪拌機的射孔支管不得使用電焊(氣焊)工具,因為電焊會破壞攪拌機的內襯塑料,支管的連接必須用專用管件進行坡口連接。
    Do not use welding tools on branches with holes as this will damage the lining. Electric welding (gas welding) tools shall not be used for perforating branch pipe of mixer, because electric welding will damage the plastic lining of mixer, and the connection of branch pipe must be beveled with special pipe fittings; electric welding (gas welding) tools shall not be used for perforating branch pipe of mixer, because electric welding will damage the plastic lining of mixer, and the connection of branch pipe must be beveled with special pipe fittings.
    在托輪和滾道之間放入木楔,以控制攪拌筒的旋轉,一定要注意;將發動機熄火,拆松液壓馬達的一根高壓油管,攪拌筒可自由旋轉,控制攪拌筒的旋轉,使維修孔轉到下部,然后打開維修孔,清理出筒內商品混凝土。此時一定要注意,產品混凝土排出完畢后,恢復商品混凝土水泥攪拌運輸車原狀。
    In order to control the rotation of the mixing cylinder, we must pay attention to putting a wedge between the supporting wheel and the raceway; turn off the engine, remove a high-pressure oil pipe of the hydraulic motor, and the mixing cylinder can rotate freely. Control the rotation of the mixing cylinder to make the maintenance hole turn to the lower part, and then open the maintenance hole to clean up the commercial concrete in the cylinder. At this time, it must be noted that after the discharge of product concrete, the commercial concrete cement mixer truck shall be restored to its original state.
    上一篇:小型混凝土攪拌車閥體維修更換
    下一篇:攪拌車換向閥出現故障是怎么回事?

    TAG:自上料攪拌車,自動上料攪拌車, 全自動攪拌車,小型攪拌車

    截屏,微信識別二維碼

    微信號:1234567

    點擊微信號復制,添加好友

     打開微信

    毒龙钻服务